UDK 621
ON THE ANALYSIS OF THE EFFECTIVENESS OF FULLY REDUNDANTSYSTEMS
P. A. Kuznetsov
Siberian State Technological University 82, Mira Av., Krasnoyarsk, 660049, Russian Federation E-mail: forubox@yandex.ru
The article discusses the reliability of automated systems, the question of the effectiveness of Reliability Improvement by reservation. Action ACS is considered from the point of view of production of a product, in the general case - some tangible results. The phenomenon, which brings the system reliability, the cost of implementing a redundant system, is studied. The actual construction of ACS requires capital costs (economic resources). The effect that increases the degree of redundancy is shown. We study a system with full redundancy, the consumption of resources for their implementation. We reveal the consequences of failure, the transition systems are faulty and dangerous condition caused by the failure of damage. The formula for determining the dependence of the effect on the costs of implementing the system, the damage caused by failure of the system, reliability and redundancy are shown. The above formulas to dependence on a small number of variables are carried out. The graphs showing the changes in terms profitability varying degrees of redundancy, graphs of the relative value of the damage and the relative value of the relative damage and reliability are provided. On the graph it is shown the critical values of the cost of systems with a certain degree of redundancy, reliability and damage, above which the economic effect is negative. It is shown under what conditions it becomes profitable or that the degree of redundancy, the boundary conditions to determine the degree of redundancy, allowing to analyze the effectiveness of control systems.
reliability, redundancy, danger, damage, efficiency
References
  1. GOST 24.702–85. Effektivnost’ avtomatizirovannykh sistem upravleniya. Osnovnye polozheniya [State Standard 24.702-85. The effectiveness of the automated control systems. Fundamentals] Available at: http:// cert.obninsk.ru/gost/554/554.html (accessed 12.02.2015).
  2. Poslavskiy M. A. Ekonomicheskaya effektivnost’ avtomatizatsii upravleniya proizvodstvom v tsvetnoy metallurgii. Diss. kand. ek. nauk [Cost-effectiveness of automation of production in ferrous metallurgy. PhD econom.sci.diss] St.Petersburg, Gipronikel' Institute Publ, 2006, 176 p.
  3. GOST 34.602–89. Tekhnicheskoe zadanie na sozdanie avtomatizirovannoy sistemy [State Standard 34.602-89. Terms of Reference for the creation of an automated system] (in Russ.) Available at: http://www.rugost.com/ index.php?option=com_content&view=article&id=96: gost-34602-89&catid=22:34&Itemid=53 (accessed 12.02. 2015).
  4. Kovalev I. V. [Analysis of the problems in the study of the reliability of the software: multi-stage and architectural aspects]. Vestnik SibGAU. 2014, No. 3(55), P. 78–92 (In Russ.).
  5. Kurochkin Yu. A., Smirnov A. S., Stepanov V. A. Nadezhnost’ i diagnostirovanie tsifrovykh ustroystv i sistem [Reliability and diagnostics of digital systems]. St. Petersburg. St. Petersburg University Publ., 1993, 320 p.
  6. Kuznetsov P. A., Beschastnaya N. A., Bakhmareva K. K., Antamoshkin O. A., Antamoshkin A. N. [Modification of the Volkovich`s-Michalevi`c method to optimize costs in the synthesis of fault-tolerant information systems]. Vestnik SibGAU. 2012, No. 6(46), P. 97–100 (In Russ.).
  7. Kovalev I. V., Kuznetsov P. A., Zelenkov P. V., Shaydurov V. V., Bakhmareva K. K. [To the question of the reliability of automated control systems with blocking protection modules]. Pribory. 2013, Vol. 6. P. 20–24 (In Russ.).
  8. Ryabinin I. A. Nadezhnost’ i bezopasnost’ strukturno-slozhnykh sistem [Reliability and safety of structural complex systems]. St. Petersburg, St. Petersburg University Publ., 2007, 276 p.
  9. GOST R 22.10.01–2001. Bezopasnost’ v chrezvychaynykh situatsiyakh. Otsenka ushcherba. Terminy i opredeleniya [State Standart R 22.10.01-200. Safety in emergencies. Damage assessment. Terms and definitions]. Available at: http://vsegost.com/Catalog/64/6474.shtml (accessed 12.02.2015).
  10. Aleksandrovskaya L. N., Aronov I. Z., Kruglov V. I., Kuznetsov A. G., Patrakov N. N., Sholom A. M. Bezopasnost’ i nadezhnost’ tekhnicheskikh sistem. Uchebnoe posobie [Safety and reliability of technical systems. Study guide]. Moscow, Logos Publ., 2004, 280 p.
  11. Lev M. Klyatis. Accelerated Reliability and Durability Testing Technology. New Jersey. John Wiley & Sons, 2012, 430 p.
  12. Sugak E. V, Vasilenko N. V. Nadezhnost' tekhnicheskikh sistem. Uchebnoe posobie dlya vysshikh uchebnykh zavedeniy [Reliability of technical systems. Study guide]. Krasnoyarsk, NII SUVPT Publ., 2000, 608 р.
  13. Okhtilev M. Yu. Sokolov B. V. Intellektual’nye tekhnologii monitoringa i upravleniya strukturnoy dinamikoy slozhnykh tekhnicheskikh ob"ektov [Intelligent technologies for monitoring and management of the structural dynamics of complex technical objects]. Moscow, Nauka Publ., 2006, 410 p.
  14. Perepelovskiy A. V., Chernenko A. F. Uchetno-analiticheskoe obespechenie khozyaystvennykh operatsiy po dogovoram pozhiznennoy renty i soderzhaniya [Accounting and analytical support for business operations on the life annuity contract and content]. Moscow, Akademiya estestvoznaniya Publ., 2013. 197 p.
  15. Bol’shaya sovetskaya entsiklopediya [The Great Soviet Encyclopedia]. Moscow, Soviet entsiklopediya Publ., 1969–1978.
  16. Lyashkov A. A., Zav'yalov A. M. [Family of surfaces is given by the coordinate transformation, and its envelope]. Inzhenernyy vestnik Dona. 2013, Vol. 1, 8 р. (In Russ.).

Kuznetsov Petr Anatol’evich – assistant, Siberian State Technological University. E-mail: forubox@yandex.ru