Научная электронная библиотека ULRICH'S Periodicals Directory

Сибирский государственный университет
науки и технологий имени академика М.Ф. Решетнева

Сибирский аэрокосмический журнал
ISSN 2712-8970 (Print) ISSN 2782-5760 (on-line)

Сведения об образовательной организации

UDK 621.22 DoI: 10.31772/2587-6066-2018-19-1-120-136
METHODS OF PREPARATION OF THE EXPERIMENT FOR INVESTIGATION OF UNIVERSAL JOINTS ON NEEDLE BEARINGS
S. P. Eresko, T. T. Eresko, E. V. Kukushkin*, V. A. Menovshikov, A. A. Orlov
Reshetnev Siberian State University of Science and Technology 31, Krasnoyarsky Rabochy Av., Krasnoyarsk, 660037, Russian Federation *E-mail: ironjeck@mail.ru
The main directions of development and improvement of performance data of universal joints needle bearings of transport technological machines are considered. The questions and tasks requiring the solution at the level of forming of new calculation procedures are specified. Modern achievements in researches of endurance failures and low-cyclic fatigue of needle bearings are considered. The main overview of the works performed in this direction is provided. The analysis of modern ideas of fatigue processes of needle bearings is given. The analysis of the current state of question on research of plastic deformation at static contact loading of needle bearings is given. Questions of forecasting of durability of needle bearings of universal joints are considered. The main questions connected with processes of forming of fatigue cracks in materials of needle bearings of universal joints in zones of power contact are considered. On the basis of the analysis of the used sources it was revealed that it is necessary to resolve the issues connected with improvement of performance data of universal joints needle bearings and questions of calculation of bearing capacity of power contact of rolling bearings and technology of receiving qualitative materials. For carrying out tests we used the test facility for universal joints allowing tests without overheat of system of braking due to cooling of working fluid and also improving operating conditions due to ensuring smoothness of regulation of braking torque. For measurement of roughness of surfaces the USB BV-7669M Profilograph profilometer was used. For measurement of hardness of surfaces of thorns of crosspiece of universal joints the HBRV-187,5 hardness gage was used. The technique of carrying out tests includes the following stages: marking of crosspieces of universal joints; measurement of roughness, hardness, geometry of crosspieces of universal joints; stage of tests; repeated measurements of roughness, hardness and geometry of crosspieces of universal joints; cutting of the studied universal joints and production of microsections for metallographic examinatons of active and passive surfaces of thorns of crosspieces of universal joints; processing of results of researches. The given technique of planning of experiments is intended for receiving experimental data of researches of universal joints at different stages of operation that will allow to estimate influences of errors of production on performance data of universal joints and to prove the reasons of formation of face and deep cracks.
endurance failures, needle bearings, modern representations of researches, test facility, design of experiments, tests of joints.
References

1. Kukushkin E. V., Menovshchikov V. A. [Main directions of development, improve and perfect the performance driveline on needle bearings]. Materialy XVI mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials XVI Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2012, P. 254–256 (In Russ.).

2. Kukushkin E. V., Menovshchikov V. A., Eresko T. T. [The analysis of modern concepts and approaches in the study of fatigue failures of needle bearings]. Materialy XVII mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials XVII Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2013, P. 287–288 (In Russ.).

3. Kotrell A. H. Teoria dislokacii [Dislocation theory]. Moscow, Mir Publ., 1969, 95 p.

4. Ekobori T. Phizika i mekhanika razrushenia i prochnosti tverdikh tel [Physics and fracture mechanics and strength of solids]. Moscow, Metallurgy Publ., 1971, 264 p.

5. Litma Uidner. [Dissemination of contact fatigue from sources of surface and subsurface origin]. Teoreticheskie osnovy inzhenernykh raschetov. 1966, No. 3, P. 94 (In Russ.).

6. Spector A. G., Zelbet B. M., Kiselev S. A. Struktura i svoistva podshipnikovikh stalei [The structure and properties of the bearing steel]. Moscow, Metallurgy Publ., 1980, 263 p.

7. Tardy P., Stiklovari Y. [Effect of vacuum treatment on the resistance bearing steel]. Stal’. 1977, No. 5, P. 452–455 (In Russ.).

8. Finkel V. M. Phizicheskie osnovi tormojenia razrushenia [Physical fundamentals of braking failure]. Moscow, Metallurgy Publ., 1977, 360 p.

9. Kukushkin E. V., Menovshchikov V. A. [Low Cycle Fatigue needle bearing]. Materialy IX Vserossiyskoy nauchno-prakticheskoy konferentsii “Aktual’nye problemy aviatsii i kosmonavtiki” [Materials IX Intern. Scientific. Conf “Current issues of aviation and cosmonautics”]. Krasnoyarsk, 2013, P. 154–155 (In Russ.).

10. Eresko T. T., Kukushkin E. V., Menovshchikov V. A. [Current status of the issue on the study of plastic deformation under static loading, the contact needle roller bearings]. Materialy X Vserossiyskoy s mezhdunarodnym uchastiem nauchno-tekhnicheskoy konferentsii “Mekhaniki XXI veku” [Materials X Russian international participation scientific conference “Mechanics of XXI century”]. Bratsk, Bratsk State University Publ., 2014, P. 37–40 (In Russ.).

11. Nesterov V. M. Razrabotka metodov ocenki soprotivlenia kontaktnoi ustalosti kinstrukcionnikh materialoc. Dokt. Diss. [Development of methods for evaluation of contact fatigue resistance of structural materials. Doct. Diss.]. Moscow, 1984, 238 p.

12. Kukushkin E. V., Menovshchikov V. A., Eresko T. T. [Questions of formation of fatigue cracks in materials needle bearing universal joints]. Materialy X Vserossiyskoy nauchno-prakticheskoy konferentsii “Aktual’nye problemy aviatsii i kosmonavtiki” [Materials X Intern. Scientific. Conf “Current issues of aviation and cosmonautics”]. Krasnoyarsk, 2014, P. 148–150 (In Russ.).

13. Gubanova A. V., Kukushkin E. V., Maslova O. E., Menovshchikov V. A. [Influence of mechanical and thermal methods of superficial work-hardening of details on their tireless pin durability of cardan hinges on needleshaped bearing]. Materialy XX mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials X Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2016, P. 403–405. (In Russ.).

14. Eresko A. S., Kukushkin E. V., Oseev D. S., Menovshchikov V. A., Pyataev D. A. [Effects of vibrations on working conditions of cardan joints]. Materialy XX mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials X Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2016, P. 405–407 (In Russ.).

15. Eresko T. T., Zhabinskaya. A. N., Kukushkin E. V., Menovshchikov V. A. [Intercommunication of primary tireless destructions with distribution of cyclic repetitive or alternating tensions of cardan hinges]. Materialy XX mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials X Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2016, P. 409–411 (In Russ.).

16. Menovshchikov V. A., Eresko S. P. Issledovanie i sovershenstvovanie igolchatikh podshipnikov kardanikh peredach transportno-tekhnologicheskikh mashin [Study and improvement of needle bearing universal joint transmission of transport and technological machines]. Krasnoyarsk, KrasGAU Publ., 2006, 283 p.

17. Pinegin S. V. Kontaktnay prochnost i soprotivlenie kachaniu [Contact resistance and rolling resistance]. Moscow, Mechanical Engineering Publ., 1969, 243 p.

18. Kostecki B. I. Trenie, smazka i iznos v mashinakh [Friction, lubrication and wear in machines]. Kiev, Engineering Publ., 1970, 396 p.

19. Kostecki B. I., Nosovskii I. G. Iznosostoikost i antifrikcionnost detaley mashin [Wear resistance and anti-friction machine parts]. Kiev, Engineering Publ., 1965, 208 p.

20. Vladimirov V. I. [Problems of physics and wear]. FHOM. 1974, No. 2, P. 23–30 (In Russ.).

21. Ekobori T. Nauchnie osnovi prochnosti i razrushenia materialov [Scientific bases of strength and fracture of materials]. Kiev, Naukova Dumka Publ., 1978, 351 p.

22. Troshchenko V. T. Prochnost metallov pri peremennikh nagruzkakh [The strength of metals under variable loads]. Kiev, Naukova Dumka Publ., 1978, 173 p.

23. Martin, Borghese, Eberhardt [Microstructural changes of bearing steel subjected to cyclic loading]. Teoreticheskie osnovy inzhenernykh raschetov. 1966, No. 3, P. 1–18.

24. Martin, Eberhardt [Determination of the possible destruction of the centers of the contact fatigue conditions rolling]. Teoreticheskie osnovy inzhenernykh raschetov. 1967, No. 4, P. 241–253.

25. Kachanov N. N. [The nature and the nature of the destruction of the working surfaces of the bearing parts]. Trudy instituta (VNIPP). 1963, No. 3 (35), P. 45–59 (In Russ.).

26. Pinegin S. V., Shevelev I. A., Gudchenko V. M., Sedov V. I., Blokhin Y. N. Vliyanie vneshnikh faktorov na kontaktnuyu prochnost’ pri kachenii [The influence of external factors on the strength of the rolling contact]. Moscow, Nauka Publ., 1972, P. 19–46.

27. Troshchenko V. T. Ustalost i neuprugost metallov [Fatigue and inelasticity metals]. Kiev, Naukova Dumka Publ., 1971, 267 p.

28. Berkovich I. I., Gromakovskiĭ D. G. [Tribology. Physical fundamentals, mechanics and engineering applications]. Samara, Samara. state. tehn. Univ Publ., 2000, 268 p.

29. Johnson K. L. Contact mechanics. Cambridge University Press, 6. Nachdruck der 1. Auflage, 2001.

30. Popov V. L. Kontaktmechanik und Reibung. Ein Lehr- und Anwendungsbuch von der Nanotribologie bis zur numerischen Simulation, Springer-Verlag, 2009, 328 p.

31. Popov V. L. Contact Mechanics and Friction. Physical Principles and Applications, Springer-Verlag, 2010, 362 p.

32. Hyun S., Robbins M. O. Elastic contact between rough surfaces: Effect of roughness at large and small wavelengths. Trobology International. 2007, Vol. 40, P. 1413–1422.

33. Ibatullin I. D. Kinetika ustalostnoy povrejdaemosti i razrushenia poverkhnostnikh sloev. [Kinetics of fatigue of damage and destruction of the surface layers]. Samara, Samara. state. tehn. University Press Publ., 2008, 387 p.

34. Regel V. R., Sloutsker A. I. [Structural and dynamic heterogeneity – the basis fizikiraz rusheniya solids]. Sorosovskiy obrazovatel'nyy zhurnal. 2004, Vol. 8, No. 1, P. 86–92.

35. Prigogine I., Kondepudi D. Sovremennay termodinamika. Ot teplovikh dvigatelei do dissipativnikh struktur. [Modern thermodynamics. From Heat Engines to Dissipative Structures]. Moscow, Mir Publ., 2002, 461 p.

36. Lokshina N. G. Razvitie konstrukcii igolchatikh podshipnikov i ikh primenenie [Development of designs of needle roller bearings and their application]. Moscow, NIINavtoprom Publ., 1967, 57 p.

37. Johnson K. L. Contact mechanics. Cambridge University Press, Cambridge, 1987, 452 p.

38. Ivanova V. S. Sovremennoe predstavlenie o prirode ustalostnogo razrushenia i novie napravlenia issledovanii. Ustalost metallov i splavov [Modern ideas about the nature of fatigue failure, and new areas of research. Fatigue of metals and alloys.]. Moscow, Nauka Publ., 1971.

39. Ivanova V. S., Terentiev V. F. Priroda ustalosti metallov. [Nature metal fatigue]. Moscow, Metallurgy Publ., 1975, 455 p.

40. Savyk A. Ya., Ivanov P. A., Kukushkin E. V., Novoselova V. O. Space-rocket machines low-cycle fatigue problems review. Materials 15 International Scientific Conference “Youth. Society. Modern science, technologies& innovations”. 2016, P. 32–34.

41. Borodii M. B. [Analysis of experimental data at low-cycle fatigue deformation]. Problemy prochnosti. 2000, No. 1, P. 13–21 (In Russ.).

42. Yu Hai Shen. Malociklovay ustalost materialov pri mnogoosnom deformirovanii. Diss. Kand. Tehn. Nauk [Low-cycle fatigue of materials under multiaxial deformation. Diss. Cand. Tehn. Sci.]. Kiev, 17 p.

43. Gusenkov A. P., Kotov P. I. Malociklovay ustalost pri neizometricheskom nagrujenii. [under non-isothermal low cycle fatigue loading]. Moscow, Mashinostroenie Publ., 1983, P. 232–238.

44. Makhutov N. A, Gadenin M. M., Gokhfel’d D. A. Uravnenia sostoaniy pri malociklovom nagrujenii [Equations of state under low-cycle loading]. Moscow, Nauka Publ., 1981, 244 p.

45. Eresko S. P., Eresko T. T., Kukushkin E. V., Menovshchikov V. A. Stend dlya ispytaniya kardannykh sharnirov [The test stand driveline]. Patent RF, no. 153924, 2015.

46. Kukushkin E. V., Menovshchikov V. A., Eresko S. P., Eresko T. T. Stend dlya ispytaniya kardannykh peredach [The test stand driveline]. Patent RF, no. 149002, 2014.

47. Eresko S. P., Eresko A. S., Eresko T. T., Eresko V. S., Kukushkin E. V., Menovshchikov V. A., Struchkov A. V., Khomenko I. I. Stend dlya ispytaniya kardannykh peredach [The test stand driveline]. Patent RF, no. 162876, 2016.

48. Kukushkin E. V., Eresko S. P., Eresko T. T., Menovshchikov V. A., Orlov A. A. [Stand construction for testing the universal joint on needle bearings in wide range of sizes with the angle changing driveline]. Transport. Transportnye sooruzheniya. Ekologiya. 2016, No. 2, P. 58–73. Doi: 10.15593/24111678/2016.02.05 (In Russ.).

49. Kukushkin E. V., Menovshchikov V. A., Eresko T. T. [Booth design for testing universal joints with needle bearings]. Materialy XIX mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials XV Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2015, P. 337–339 (In Russ.).

50. Eresko A. S., Eresko S. P., Eresko T. T., Kukushkin E. V., Menovshchikov V. A., Orlov A. A. [Calculation of the hydraulic system of brake device of stand for the test of transmissions of transporttechnological machines]. Transport. Transportnye sooruzheniya. Ekologiya. 2016, No. 4, P. 60–79. Doi: 10.15593/24111678/2016.04.06 (In Russ.).

51. Eresko S. P., Eresko T. T., Kukushkin E. V., Menovshikov V. A., Khomenko I. I. [Planning of experiment on research of cardan transmissions on the needleshaped bearing]. Materialy XII Mezhdunarodnoy nauchno-prakticheskoy konferentsii “Aktual’nye problemy aviatsii i kosmonavtiki” [Materials XII Intern. Scientific. Conf “Current issues of aviation and cosmonautics”]. Krasnoyarsk, 2016, P. 368–370 (In Russ.).

52. Eresko S. P., Eresko T. T., Kukushkin E. V., Menovshchikov V. A., Khomenko I. I. [Planning of experiment on research of cardan transmissions on the needle-shaped bearing]. Vestnik SibGAU. 2016, No. 17, No. 4, P. 1062–1071 (In Russ.).

53. Kukushkin E. V., Menovshchikov V. A., Eresko S. P., Eresko T. T. Kardannyy sharnir [Joint]. Patent RF, no. 141878, 2014.

54. Kukushkin E. V., Menovshchikov V. A., Orlov A. A., Eresko S. P., Eresko T. T. Kardannyy sharnir [Joint]. Patent RF, no. 146989, 2014.

55. Gadisov R. A., Eresko A. S., Kukushkin E. V. [Automation of measuring of data-outs of elements of hydraulic drive]. Materialy XII Mezhdunarodnoy nauchno-prakticheskoy konferentsii “Aktual’nye problemy aviatsii i kosmonavtiki” [Materials XII Intern. Scientific. Conf “Current issues of aviation and cosmonautics”]. Krasnoyarsk, 2016, P. 355–357 (In Russ.).

56. Eresko S. P., Eresko T. T., Kukushkin E. V., Menovshchikov V. A. [Comparative analysis of structures universal joints unequal angular velocity]. Vestnik SibGAU. 2015, No. 16, P. 720–728 (In Russ.).

57. Eresko T. T., Kukushkin E. V., Menovshchikov V. A. [The design of the universal joint with replaceable spikes spider]. Materialy XVIII mezhdunarodnoy nauchnoy konferentsii “Reshetnevskie chteniya” [Materials XV Intern. Scientific. Conf “Reshetnev reading”]. Krasnoyarsk, 2014, P. 298–300 (In Russ.).

58. Kukushkin E. V., Menovshchikov V. A., Eresko T. T. [New universal joint design]. Materialy XI Vserossiyskoy nauchno-prakticheskoy konferentsii “Aktual’-nye problemy aviatsii i kosmonavtiki” [Materials XI Intern. Scientific. Conf “Current issues of aviation and cosmonautics”]. Krasnoyarsk, 2015, P. 211–213 (In Russ.).

59. Kukushkin E. V., Eresko T. T., Mednikov D. M. New construction of universal joints. Materials 14-th International Scientific Conference “Youth. Society. Modern science, technologies & innovations”. 2015, P. 232–234.

 


Eresko Sergey Pavlovich – Dr. Sc., corresponding member of Academy of Science of Higher Education

Institutions of the Russian Federation, professor, Institute of Mechanical Science and Mechatronics, Department of

Principle of machine construction, Reshetnev Siberian State University of Science and Technology. E-mail:

ereskosp@mail.sibsau.ru.

Eresko Tatyana Trofimovna – Dr. Sc., Docent, Institute of Mechanical Science and Mechatronics, head

of Department of Principle of machine construction, Reshetnev Siberian State University of Science and Technology.

E-mail: ereskott@mail.ru.

Kukushkin Evgeny Vladimirovich – assistant of Department of Principle of machine construction, Institute

of Mechanical Science and Mechatronics, Reshetnev Siberian State University of Science and Technology. Е-mail:

ironjeck@mail.ru.

Menovschikov Vladimir Alexandrovich – Dr. Sc., professor of Department of Principle of machine construction,

Institute of Mechanical Science and Mechatronics, Reshetnev Siberian State University of Science and Technology.

Е-mail: menovchikovva@mail.sibsau.ru.

Orlov Aleksandr Aleksandrovich – postgraduate student, Department of Fundamentals of machine design,

Institute of Mechanical Engineering and Mechatronics, Reshetnev Siberian State University of Science and Technology.

E-mail: ironjeck@mail.ru.


  METHODS OF PREPARATION OF THE EXPERIMENT FOR INVESTIGATION OF UNIVERSAL JOINTS ON NEEDLE BEARINGS